Wieght Question, 452V & VX-II 6-18AO w/ Turrets

bigrobbierob · Post by **bigrobbierob** » Sat May 23, 2009 12:55 am

Want to know if my CZ452 Varmint with a Leupold VX-II 6-18AO, target turrets, will make wieght for both divisions of smallbore silhouette? Anybody running this sort of combo? Asking as i dont have a scale here in the house. Thanks.

Rob

Ghostofwar · Post by **Ghostofwar** » Sat May 23, 2009 11:37 am

I used that exact set up for a while. It made weight by a few ounces. But I don't know what kind of rings you have. If they are light weight, you should be fine.

BlauBear · Post by **BlauBear** » Sat May 23, 2009 2:19 pm

Ditto! It's a great setup and a true classic with BKL rings, so shoot and enjoy. It's very hard to improve on that setup!

bigrobbierob · Post by **bigrobbierob** » Sat May 23, 2009 7:39 pm

I am running the Leupold Steel 22 rings. THink those will push me over wieght?

BlauBear · Post by **BlauBear** » Sat May 23, 2009 7:53 pm

Better to check. If it's over, put out feelers for a set of BKL's.

bigrobbierob · Post by **bigrobbierob** » Sat May 23, 2009 11:58 pm

I had a set of BKL's when I first bought the rifle, but the darn things shot loose from the rail. Wont be trying those anymore.

Jason · Post by **Jason** » Sun May 24, 2009 6:52 am

A large portion of the rings on silhouette rifles are BKLs and I've been shooting them on my Anschutz 1712 and CZ 452 Varmint for years. If they shot loose, then it wasn't the rings' fault. I don't use any Loctite on mine at all, just torque them to 20 in lbs on the rail and 15 in lbs on the rings. Haven't had them come loose yet. Make sure the screws aren't lubed. If necessary, clean them well and use a bit of blue Loctite (easy to remove later).

Edit: should have said "easy" instead of "each" there

sobrbiker883 · Post by **sobrbiker883** » Tue May 26, 2009 5:18 am

bigrobbierob wrote:I had a set of BKL's when I first bought the rifle, but the darn things shot loose from the rail. Wont be trying those anymore.

Sometimes BKL's take quite a stiff twist to clamp. I've usually gon hand tight plus 3/4 turn with an allen wrench and haven't ever had mine come loose......
If you still have them may want to try again, cause those darn things are working great on lots of rifles, or toss them in the marketplace-someone'll take 'em off your hands for sure.

BlauBear · Post by **BlauBear** » Tue May 26, 2009 5:52 am

When tightening onto the rifle it's hard to over tighten BKL's - I don't think they'll break... Tighten them until the scope doesn't move, then tighten a bit more. They are stiffer than other mounts, and they will fool you.

bigrobbierob · Post by **bigrobbierob** » Wed May 27, 2009 2:53 am

Yeah I would try them again, but they went into the garbage about 8 months ago. The Leupold rings worked right out the box, saw no need to keep the BKL's.

ntyree · Post by **ntyree** » Fri May 29, 2009 5:16 am

got my digital scales in last night and weighed my varmint. with plastic magazine in rifle both turret covers on and sling swivels still in the stock from the factory i came in at 8lbs 6.4 oz

thats with a 452 v, rifle basix trigger, cz steel rings and a lupy fixed 25 power scope ( the scope change got me under weight from a tasco 6x24 variable and millet rings even though the cz rings are probably heavier than the millets
.

nick

Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets

Re: Wieght Question, 452V & VX-II 6-18AO w/ Turrets