Legal Stock?
Posted: Fri Jul 29, 2011 3:08 pm
Where is the probably choice?
How deep is the for end? Over 2"?
Innocent Mary
https://www.steelchickens.com/forums/
Legal Stock?
Page 1 of 1
Re: Legal Stock?
Posted: Fri Jul 29, 2011 4:50 pm
Re: Legal Stock?
Posted: Fri Jul 29, 2011 5:11 pm
Mary,
PM
PM
Re: Legal Stock?
Posted: Fri Jul 29, 2011 5:34 pm
I say "absolutely".
If the stock is too deep at the forarm... a wood rasp and about 60 seconds worth of work would rectify that.
If the stock is too deep at the forarm... a wood rasp and about 60 seconds worth of work would rectify that.
Re: Legal Stock?
Posted: Fri Jul 29, 2011 5:55 pm
Ok thanks for the info!
Re: Legal Stock?
Posted: Fri Jul 29, 2011 5:57 pm
depens on if the match director believes it's "twisted so as to deviate from convential configurations" - clear as mud eh?
other than hunting rifle where thumbholes are called out as not legal, i would let it be used.
Stock: The stock must be traditionally styled and may not be bent and/or twisted so as to deviate from
conventional configurations such as factory rifle stocks or silhouette stocks as manufactured by Fajen,
McMillan, H-S Precision, and others. The forend, including the trigger guard mounts and screws, shall not
exceed 2 1/4 inches wide, and 2 1/4 inches deep measured from the centerline of the bore. Magazines do
not have to conform to stock measurements but those that extend below the stock line may not be used as
support as per Rule 3.I(h) and 3.14. The forend shall extend a minimum of 8 inches forward of the forward
edge of the receiver ring. The comb shall not extend above the centerline of the bore, but Monte Carlo roll
may rise 1/2 inch on the off side. The toe of the stock including buttplate or recoil pad shall be no more
than 7 inches below the centerline of the bore. Buttplate or recoil pad may not extend below the lower line
of the stock.
other than hunting rifle where thumbholes are called out as not legal, i would let it be used.
Stock: The stock must be traditionally styled and may not be bent and/or twisted so as to deviate from
conventional configurations such as factory rifle stocks or silhouette stocks as manufactured by Fajen,
McMillan, H-S Precision, and others. The forend, including the trigger guard mounts and screws, shall not
exceed 2 1/4 inches wide, and 2 1/4 inches deep measured from the centerline of the bore. Magazines do
not have to conform to stock measurements but those that extend below the stock line may not be used as
support as per Rule 3.I(h) and 3.14. The forend shall extend a minimum of 8 inches forward of the forward
edge of the receiver ring. The comb shall not extend above the centerline of the bore, but Monte Carlo roll
may rise 1/2 inch on the off side. The toe of the stock including buttplate or recoil pad shall be no more
than 7 inches below the centerline of the bore. Buttplate or recoil pad may not extend below the lower line
of the stock.
Re: Legal Stock?
Posted: Sat Jul 30, 2011 6:20 am
toe may be close as well, good price though! neat lookin too
Re: Legal Stock?
Posted: Sat Jul 30, 2011 6:20 am
toe may be close as well, good price though! neat lookin too
Re: Legal Stock?
Posted: Sat Jul 30, 2011 1:33 pm
same stock used on 10/22's for standard class, yea its def. legal.
BH if you get one let us know how you like, been thinking about getting one myself...
BH if you get one let us know how you like, been thinking about getting one myself...
Re: Legal Stock?
Posted: Sun Jul 31, 2011 6:11 pm
then would this be legal as well for standard class?
http://www.boydsgunstocks.com/SS-EVOLUT ... 984-sp.htm
http://www.boydsgunstocks.com/SS-EVOLUT ... 984-sp.htm
Re: Legal Stock?
Posted: Sun Jul 31, 2011 6:53 pm
That stock just needs a little of material added to the front of the forearm in order to meet the minimum 8" in front of the receiver (which is a rule that I don't understand the purpose of).calixt0 wrote:then would this be legal as well for standard class?
http://www.boydsgunstocks.com/SS-EVOLUT ... 984-sp.htm