Page 1 of 2
Rimfire Question
Posted: Sat Oct 11, 2008 11:50 am
by Jim Beckley
If a .22 shell is improperly primed or is loaded without powder and the case is fired and the bullet doesn't make it all the way out the barrel, what do you think would happen? Split case, any damage to receiver or barrel, how about the bolt?
Posted: Sat Oct 11, 2008 12:15 pm
by BlauBear
If you're talking about an extreme squib with just some primer, there's no damage unless you fire another round behind it. You may hear an odd double pop, the case would probably rupture and the gasses would jet out the relief port (or ports) drilled in the receiver for just such a possibility, and the bolt would probably be tough to open. Both bullets may or may not leave the bore, and you may or may not need clean shorts.
It probably won't damage the rifle but even if you can get the bullets out of the bore, have the rifle checked by a gunsmith before using it again. I've had some under loaded squibs that barely went 20 meters before plopping into the dirt, and those were funny, but so for none so extreme they didn't clear the bore. Case ruptures are another matter since those slice right through any misplaced fingers. Fortunately, I only have a scar on my thumb from that learning experience...
Posted: Sat Oct 11, 2008 2:19 pm
by cslcAl
I saw this happen at a SB match at Ridgway last year. The shooter was using RWS ammo in a 54MS Anschutz. He did not realize he had fired a sqib load. When he fired the next round it blew the extractor off the bolt. Also the barrel had to be replaced. Al F.
Rimfire Question
Posted: Sat Oct 11, 2008 2:46 pm
by Jim Beckley
A buddy of mine blew the extractor off from his Rem 700 bolt about a month ago, didn't kinow if it was double primed, double charged, or what. It didn't harm the barrel or anything.
Posted: Sat Oct 11, 2008 5:04 pm
by BlauBear
cslcAl wrote:Also the barrel had to be replaced. Al F.
That surprises me some, but replacing the barrel on a competition rifle after something like that probably is a good idea, even if it's just a precaution.
Posted: Tue Oct 14, 2008 2:50 am
by _Shorty
Firing another round after one gets stuck in the barrel will likely put a noticable bulge in the barrel. Doesn't necessarily affect accuracy, so they say. But I can't see how it wouldn't. Lead doesn't spring back.
BlauBear wrote:That surprises me some, but replacing the barrel on a competition rifle after something like that probably is a good idea, even if it's just a precaution.
Ringed barrels
Posted: Tue Oct 14, 2008 4:26 am
by Travelor
My experience is that firing a second bullet down the barrel into an obstruction such as a lodged bullet with put a ring (or loose spot) in the barrel.
George
Re: Ringed barrels
Posted: Tue Oct 14, 2008 5:51 am
by BlauBear
Travelor wrote:My experience is that firing a second bullet down the barrel into an obstruction such as a lodged bullet with put a ring (or loose spot) in the barrel.
George
That I believe, though I'd be very surprised if a rimfire barrel actually bulged. Barrel steel is pretty stout and a lot of the force will channel out the relief ports, but it's still a strong pressure wave front that has to go some where before it will push back against the bolt.
Re: Ringed barrels
Posted: Tue Oct 14, 2008 9:49 am
by _Shorty
I just said that. ;)
Travelor wrote:My experience is that firing a second bullet down the barrel into an obstruction such as a lodged bullet with put a ring (or loose spot) in the barrel.
George
Rimfire Question
Posted: Tue Oct 14, 2008 9:55 am
by Jim Beckley
At a sight in service that the Ben Avery Club offers each year, one fellow came up and said that he couldn't get his gun to shoot, after checking all the screws, I put it on a bag and took a shot at a plastic bottle that was on the berm, it hit the bottle, the second and third shot were about a foot off in either direction, while sitting there trying to figure what was wrong, the guy says "do you think this has anything to do with it", there was a bulge about 4 inches froward of the chamber area, but that was a bigbore, haven't seen one with a smallbore.
Posted: Tue Oct 14, 2008 5:56 pm
by BlauBear
Mach 2 wrote:...the breech end chamber is also "corked" with an expanded brass case.
Too true, meaning a case rupture before it vents. And you're right, the main pressure wave will have passed before that happens.
Posted: Tue Oct 14, 2008 6:46 pm
by Bob Mc Alice
I ask you........What subject cant be found on Google?
http://www.google.com/search?source=ig& ... gle+Search
Posted: Tue Oct 14, 2008 8:20 pm
by _Shorty
Posted: Mon Oct 20, 2008 11:00 am
by GTKF
Happened this past Saturday at the Staten Island SB match. 1712 with Lapua Super Club.
After checking the shoooter reported a ring in the barrel. He's using it as an excuse to rebarrel with a Lilja
Posted: Mon Oct 20, 2008 11:33 am
by BlauBear
Hey, whatever works...