A question about scope installation
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
A question about scope installation
If someone accidently grabbed a superglue bottle instead of a blue loctite bottle, can the screws be removed with heat? Like putting,the tip of A soldering iron on the screwhead?
-
- AAA Poster
- Posts: 684
- Joined: Tue Jun 11, 2013 3:07 pm
- Location: West Monroe, LA
Re: A question about scope installation
I've tried the heating of screws with a soldering iron tip pressed to it with no luck. I would think it is material dependent as far as how much the heat transfers so your mileage may vary. You could try solvents to dissolve the glue or at least weaken it, but be wary of the liquids making contact with the stock because it will certainly strip some finish. Especially if you're using acetone.
I am NOT Danny Hatch.
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
Re: A question about scope installation
Hmmmmm, I may have to buy a small angle grinder to cut the scope out of the rings. My current grinder is a little bulky for this kind of work.
-
- A Poster
- Posts: 127
- Joined: Tue Jun 06, 2006 9:36 pm
- Location: Corpus Christi, TX
Re: A question about scope installation
First... try your wife's hair dryer once you have separated the wooden parts from the steel parts. I've seen it work more often than fail and you aren't going to tear anything up.
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
Re: A question about scope installation
Thank you gentlemen for the advice.
- OldRanger
- AAA Poster
- Posts: 992
- Joined: Thu Jun 06, 2013 9:00 am
- Location: Missoula, MT
- Contact:
Re: A question about scope installation
Go back under your bridge Troll-Boy!
Oh, I do have a ww2 flame thrower if you need a tad more heat.
Oh, I do have a ww2 flame thrower if you need a tad more heat.
I buy all my guns from t-rex. He's a small arms dealer.
-
- A Poster
- Posts: 204
- Joined: Thu Aug 06, 2009 3:41 pm
Re: A question about scope installation
Not my idea and I have no experience trying it, but I have some friends who make stocks and repair old ones----they have told me Acetone will soften it and allow the bond to be broken.
Good luck---have done my fingers, but warm water will generally get that.
Good luck---have done my fingers, but warm water will generally get that.
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
Re: A question about scope installation
Acetone? Is that the same stuff as mail polish remover? I was told that works too.
I like the chemical treatment over heat. I am less likely to damage anything.
I like the chemical treatment over heat. I am less likely to damage anything.
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
-
- AAA Poster
- Posts: 684
- Joined: Tue Jun 11, 2013 3:07 pm
- Location: West Monroe, LA
Re: A question about scope installation
There is acetone in nail polish remover.
Head to a hardware store and grab some acetone. Apply it with qtips to limit contact with everything else. Acetone can strip finish and color. Great stuff but be cautious!
I am NOT Danny Hatch.
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: A question about scope installation
If you have to cut the rings, use a high quality hacksaw.
More control than powered abrasives and no grit from abrasives landing in important parts. It is a lot easier cleanup.
I worked for 3 different gun stores. Stuck rings for various reasons are more common than you would think.
More control than powered abrasives and no grit from abrasives landing in important parts. It is a lot easier cleanup.
I worked for 3 different gun stores. Stuck rings for various reasons are more common than you would think.
-
- Uber Master Poster
- Posts: 2746
- Joined: Wed Apr 12, 2006 2:34 pm
- Location: Casa Grande, AZ
Re: A question about scope installation
Good advice AB if the rings are AL. If they are steel, a cut-off wheel in a dremmel tool would work. I would cut the rings next to the screws to avoid damaging the scope.
- Bob259
- Uber Master Poster
- Posts: 4337
- Joined: Sat Jul 15, 2006 7:16 pm
- Location: Phoenix, AZ
Re: A question about scope installation
Yes it is and usually removes super glue.
F Troop - Southwest Outpost
Proud Member of the Ram Slammers US Division (Two Bob)
Proud Member of the Ram Slammers US Division (Two Bob)
- DavidABQ
- Expert Master Poster
- Posts: 1819
- Joined: Mon Jul 27, 2009 9:33 pm
Re: A question about scope installation
A Dremel doesn't seem industrial enough to cut through something like well made scope rings? Are you sure they can do the job?
-
- AA Poster
- Posts: 317
- Joined: Sun Mar 08, 2009 5:42 pm
Re: A question about scope installation
I assume you're talking about ring screws that hold the two halves together and not base to receiver rings?
Since heat from a propane torch will loosen Loc-Tite 609, I'm sure it would have an impact on superglue, though I'm equally certain the undesired learning about the heat impact on an aluminum scope body, seals, plastic components, etc....isn't necessarily desired. In light of this, I would clamp the rifle or barreled action in a padded vise and get a well centered punch mark on the screw. After placing the rifle/barreled action in my mill vise (again padded), I would use a left hand twist bit at low speed. Don't have a mill? A good drill press with a decent vise works equally well.
I've used this technique to remove some really nasty bolts/screws from small items up to 3/4 " grade 5 bolts used to secure farm implements.
Good luck.