Re-coloring scope knobs?
- acorneau
- AAA Poster
- Posts: 888
- Joined: Sun Feb 22, 2015 12:12 pm
- Location: Houston
Re-coloring scope knobs?
Anybody know how to re-paint the markings on scope knobs?
The elevation adjustment knob on my Weaver T-24 has been used so much that all the yellow coloring is gone and it's hard for me to see the lines and numbers. At first I thought it was just hand-grime so I gave it a scrub with some soap and an old toothbrush, but that didn't do anything appreciable.
If not I may have to try to find a replacement or start carrying my reading glasses in my vest.![Nerd :-B](./images/smilies/26.gif)
The elevation adjustment knob on my Weaver T-24 has been used so much that all the yellow coloring is gone and it's hard for me to see the lines and numbers. At first I thought it was just hand-grime so I gave it a scrub with some soap and an old toothbrush, but that didn't do anything appreciable.
If not I may have to try to find a replacement or start carrying my reading glasses in my vest.
![Nerd :-B](./images/smilies/26.gif)
Allen Corneau
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: Re-coloring scope knobs?
I would try somebody that makes jewelry as a hobby first.
Second I would try a real jeweler or a antique clock/watch repair shop to get an estimate. It would probably be too expensive but you never know.
A real grandfather clock person can do some amazing things. Wayne Merrier comes to mind for these type things.
Second I would try a real jeweler or a antique clock/watch repair shop to get an estimate. It would probably be too expensive but you never know.
A real grandfather clock person can do some amazing things. Wayne Merrier comes to mind for these type things.
-
- A Poster
- Posts: 108
- Joined: Mon Feb 18, 2019 1:18 pm
- Location: Morgantown, WV
- Contact:
Re: Re-coloring scope knobs?
Are the marks engraved (cuts in the metal) or just painted on the metal? If engraved, and I think they are, start with cleaning the knobs up real well with some solvent and a brush. Maybe a toothbrush. Then get some slow drying white paint and wipe it on. I’ve used oil based paint. Then take a paper towel barely dampened with paint thinner and gently wipe off the excess paint from the surface. I say gently because if you wipe too hard you’ll wipe it out of the engraving and be back where you started. I’ve done this a bunch with different things over the years.
- acorneau
- AAA Poster
- Posts: 888
- Joined: Sun Feb 22, 2015 12:12 pm
- Location: Houston
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: Re-coloring scope knobs?
If you diy as pdeal suggested, I have had better success taking away the excess of oil based paint with a dry cotton swab that has a wood shaft but I remove the excess paint before it starts to dry and use the swab parallel to the painted surface and not on end. A swab slightly moistened with mineral spirits would be something else to try after the paint is dry but I would guess the excess oil based paint would be much more difficult to remove after it is completely dry. I would still use the smallest point shaped artist brush you can find with good light and magnification. I have only used the cotton swabs with outdoor art projects not anything as detailed as a scope knob. I now seem to remember that there is some rub on gold or silver foil sold for applications where engraving needs to be filled. I do not know how durable that would be but it would be worth investigating.
Last edited by atomicbrh on Tue Aug 17, 2021 6:54 am, edited 1 time in total.
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
- psteiger
- AAA Poster
- Posts: 773
- Joined: Fri Jun 09, 2006 10:45 am
- Location: Friendswood, Texas
Re: Re-coloring scope knobs?
Can't you get a new one from Weaver? I did a few years back.....
- acorneau
- AAA Poster
- Posts: 888
- Joined: Sun Feb 22, 2015 12:12 pm
- Location: Houston
Re: Re-coloring scope knobs?
Finally got around to doing something about my situation.
Not a perfect job but 100 times better than before. I might have to go back and do a second coat to fill it in just a bit more.
![Image](http://allencorneau.com/pictures/ScopeCap.MOV)
Not a perfect job but 100 times better than before. I might have to go back and do a second coat to fill it in just a bit more.
![I dont know :-??](./images/smilies/106.gif)
Allen Corneau
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: Re-coloring scope knobs?
What method did you decide to use?
- acorneau
- AAA Poster
- Posts: 888
- Joined: Sun Feb 22, 2015 12:12 pm
- Location: Houston
Re: Re-coloring scope knobs?
I used a tiny brush to get it in the crevices and wiped the excess off with paper towels. I think a small rubber/silicone scrapper or squeegee for the first pass before coming in with a paper towel would yield a cleaner result. Probably just one of those things that takes a bit of practice and playing around with different techniques to get it dialed in.
Allen Corneau
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: Re-coloring scope knobs?
Paint or faux gold leaf?
Photo will not show for me.
Photo will not show for me.
- acorneau
- AAA Poster
- Posts: 888
- Joined: Sun Feb 22, 2015 12:12 pm
- Location: Houston
Re: Re-coloring scope knobs?
Allen Corneau
-
- Master Poster
- Posts: 1293
- Joined: Sat Apr 15, 2006 7:24 pm
- Location: Rural Mississippi
Re: Re-coloring scope knobs?
That looks better than factory to me!
Much more brilliant and easier to see.
Much more brilliant and easier to see.